Paver Calculator

Work out how many pavers you need for a patio, path or driveway — plus the bedding sand and base material underneath. Enter your numbers and press Calculate.

Calculate pavers, sand & base

Choose your units and input method, enter the dimensions, then press Calculate.

Units
Input method
Paved area
m
m
Paver size
Or choose "Custom" to enter your own.
mm
mm
Joints, bedding & base
mm
Usually 2–3 mm between pavers.
cm
3–4 cm of sharp sand after compaction.
cm
10–15 cm patio; 15–20 cm driveway.
%
5% simple, 10% for curves and cuts.
Results also update as you type.

Your paver & materials estimate

Live
Pavers needed (with waste) —
Area to pave —
Pavers per m² / ft² —
Bedding sand —
Base material —
Base weight (approx.) —

Pavers are rounded up to whole units. Base weight is based on compacted crushed stone at 2,000 kg/m³ (or 3,370 lb/yd³).

Order 5–10% extra pavers. Cuts break some pieces, and you want spares for repairs later. Matching a discontinued paver colour a year from now is much harder than ordering a few extra today.

How to Use the Paver Calculator

Three inputs, one button, and you have a full materials list.

Step 1 — measure the paved area

Measure the length and width of the patio, path or driveway in metres or feet. For an L-shaped area, split it into two rectangles and enter them separately. Subtract any beds, planters or trees inside the area. Enter the total — or use the Known area mode if you already know it.

Step 2 — choose the paver size

Pavers come in standard sizes: 200 × 100 mm (small block paving), 300 × 300 mm (classic patio), 400 × 400 mm (large patio), and 600 × 300 mm (modern rectangular). Pick a preset or choose "Custom" to enter the exact size from your supplier. Joint width is usually 2–3 mm.

Step 3 — set the bedding and base depths and press Calculate

Pavers need a 3–4 cm bedding layer of sharp sand over a 10–15 cm compacted base for patios and paths (or 15–20 cm for driveways). The base carries the load — too thin and the pavers sink. Press Calculate to see the paver count, sand volume and base volume.

Pavers per square metre by size (with 3 mm joints)
Paver size Per m² Per yd² Typical use
200 × 100 mm4840Block paving, driveways
200 × 200 mm2420Paths, small patios
300 × 300 mm119.2Classic patios
400 × 400 mm6.25.2Large patios
450 × 450 mm4.84.0Modern patios
600 × 300 mm5.54.6Contemporary patios
600 × 600 mm2.72.3Large format, fewer joints

Reading the results

Pavers needed is the count to order, including your waste allowance. Bedding sand is the volume of sharp sand for the layer under the pavers — order bulk if you can. Base material is the volume of compacted crushed stone — the actual delivered volume is 20–30% higher because loose stone bulks up before compaction. Base weight helps when the supplier quotes by the tonne.

Common paver mistakes

  • Skipping the compacted base — pavers sink within a season on soft ground.
  • Using builder's sand for bedding instead of sharp sand — it does not compact firmly.
  • Spreading bedding sand too thick (over 5 cm) — the pavers rock and shift underfoot.
  • Forgetting the 5–10% cutting allowance, then running short on the last row.
  • Laying pavers tight with no joints — they chip and crack against each other.
  • Using the wrong base depth for the use. Patios need 10–15 cm; driveways need 15–20 cm.

Paver Calculator FAQ

Short answers to the questions people ask most about paving.

How many pavers do I need per square metre?

Divide 1 square metre by the area of one paver including its joint. A 200 × 100 mm paver with a 3 mm joint covers about 0.0209 m², so you need roughly 48 pavers per square metre. A 300 × 300 mm paver needs 11 per square metre, a 400 × 400 mm needs 6.2, and a 600 × 300 mm needs 5.5. Always add 5 to 10 percent for cutting.

How deep should the base be under pavers?

Patios and footpaths need a 10 to 15 cm compacted base (usually MOT Type 1 or crushed stone). Driveways that take vehicles need 15 to 20 cm. On soft clay ground, add an extra 5 cm. The base carries the load — if it is too thin, the pavers will sink and shift within a season.

How much sand goes under pavers?

Bedding sand goes down 3 to 4 cm deep after compaction, over the compacted base. For a 20 m² patio at 3 cm deep, you need 0.6 cubic metres of sharp sand, which weighs about 960 kg. Use sharp sand or paver bedding sand, not builder's sand or play sand — those do not compact firmly.

How much waste should I allow for cutting pavers?

Add 5 percent for a simple rectangular patio with few cuts, and 10 percent for a patio with curves, angles or many obstacles. Cutting breaks some pavers, and you need spares for repairs later. It is much easier to order extra at the start than to match a discontinued paver colour a year later.

What is the best base for a paver patio?

For most patios and paths, use MOT Type 1 or crushed stone compacted to 10 to 15 cm, then a 3 to 4 cm bedding layer of sharp sand on top. For driveways, increase the compacted base to 15 to 20 cm. On heavy clay, add a geotextile membrane under the base to stop it mixing with the subsoil.